Remarkable enhancement of the photocatalytic activity of ZnO nanorod array by utilizing energy transfer between Eosin Y and Rose Bengal for visible light-driven hydrogen evolution

In this work, we suggested that an efficient ZnO-based photocatalyst can be prepared utilizing energy transfer among organic dyes for visible light-driven hydrogen evolution. Followed this idea, a photocatalytic system containing Eosin Y, Rose Bengal, ZnO nanorod array and Pt was fabricated. Meanwhile, photocatalytic H₂ evolution over the as-prepared photocatalytic system was explored. The results indicate that the visible photocatalytic activity of ZnO nanorod array can be obviously enhanced utilizing the energy transfer between Eosin Y and Rose Bengal. This photocatalytic system possesses high activity for visible light-driven H₂ evolution. A rate of H₂ evolution of approximate 0.52 L m^?2 h^?1 was achieved under optimal condition, which is 130% and 58% higher than those of the photocatalytic systems containing individual dye, respectively. The present results may reveal a new strategy for preparation of efficient visible photocatalyst.     

透明红外硫系薄膜非均匀性检测及影响因素

薄膜非均匀性的无损检测对于制备大面积高质量的红外透明薄膜尤为重要。针对红外薄膜光学均匀性难以获取的困难,提出了一种同时获得单层透明红外薄膜厚度和折射率均匀性的无损检测方法。实验上,通过磁控溅射法在二氧化硅衬底上制备了厚度约1.4μm红外透明Ge-Sb-Se硫系薄膜,然后在该薄膜上标定出36个80μm×80μm区域,利用显微傅里叶红外光谱仪测得该36个区域的透射谱,通过分段滤波的方法滤除背景噪声,运用改进的Swanepoel方法计算得到了薄膜每一个区域的厚度和折射率,进而精确获得该薄膜的厚度和折射率均匀性,结果表明精度优于0.5%。     

5G光模块技术及方案对比

论述了5G光模块的技术和产业化发展现状,分析了4种波分复用技术应用于5G前传网络的优缺点,给出了后续5G光模块发展的策略建议.     

数字化羊绒测色法及其在长度测量中的应用

针对光电法测试纤维长度等性质时,存在纤维的透光及反光信号与颜色高度相关的问题,采用数字化方法表征羊绒的颜色类别并精准地测量羊绒的长度。将彩色光电耦合器作为测色传感器,搭建了更适合纤维材料的测色装置;通过颜色模型在3种色空间的转换,得到3类颜色的羊绒在三维色空间的分布;基于系列实验,创建了有色羊绒的光学参数即无穷厚时的表观反射率表观反射率与测色装置计算的亮度指标之间的换算模型,并用实验证明采用测得的表观反射率可计算得到准确的须丛线密度曲线,从而可用光电法精准测量有色羊绒的长度。结果表明,该测色方法的测样面积大,代表性好,成本低,同时可用于其他纤维和纺织品的颜色测量。     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

Shape from focus based on 3D structure tensor using optical microscopy

Shape from focus (SFF) is a widely used passive optical method for 3D shape reconstruction. In SFF, a focus measure, which is used to estimate the relative focus level, plays a critical role in depth estimation. In this article, we present a new focus measure for accurate 3D shape estimation in optical microscopy based on the analysis of 3D structure tensor. First, the 3D tensors are computed from the input image sequence for each pixel. Then, each tensor is decomposed into point, curve, and surface tensors by decomposing tensors into eigenvalues and eigenvectors. Finally, the surfaceness is used to measure the quality of sharpness. The proposed focus measure provides accurate focus values and better resistance against noise. The proposed measure is evaluated by conducting experiments using image sequences of simulated and microscopic real objects. The comparative analysis demonstrates the effectiveness of the proposed focus measure in recovering 3D shape.     

Polytetrafluoroethylene-intercalated MXene membranes with good photothermal performance for enhanced laser ignition

Photothermal effect has been widely used in many areas such as cancer therapy, photothermal energy harvesting, and laser ignition. However, exploring reliable and efficient free-standing energy converter for enhancing the photothermal performance is still a challenge. Herein, free-standing membrane based on two-dimensional MXene (Ti₃C₂) nanosheets and polytetrafluoroethylene (PTFE) was fabricated and characterized by X-ray diffraction, scanning electron microscopy and differential scanning calorimetry, which demonstrated a drastic temperature rise by laser irradiation and was further used as energy converter for enhancing the photothermal performance of laser ignition. Furthermore, the initiating power of the laser initiator can be largely reduced by adding a thin layer of MXene/PTFE membrane above the B/KNO₃ cylinder. This work can give great promise for MXene-based membranes as the laser energy converter for reducing the initiating energy and promote the development of laser initiators with low initiating energy.     

用于低损耗特种玻璃熔炼的高纯致密锆英石的研制

以纯度大于99.9%(质量分数)的高纯ZrO₂和SiO₂为原料,少量TiO₂为添加剂,采用高温固相法合成高纯锆英石(ZrSiO₄)粉料。研究温度和反应时间对高纯锆英石合成效率的影响,发现粒度小于50 μm的原料粉末经1 500 ℃反应48 h后,ZrSiO₄相的含量可以达到95.77%(质量分数)。将合成的高纯锆英石粉料球磨并冷等静压成型后,在1 550 ℃高温烧结成高纯致密锆英石砖。高纯致密锆英石中杂质Fe的含量仅为29 μg/g,Cu的含量小于1 μg/g,是普通商用致密锆英石的1/10;对磷酸盐玻璃静态光吸收损耗的影响仅为普通致密锆英石材料的1/3。将这种高纯致密锆英石材料用于激光玻璃窑炉,有助于降低玻璃对1 053 nm激光的损耗,提升激光玻璃的激光性能。     

Constructing General Orthogonal Fractional Factorial Split-Plot Designs

While the orthogonal design of split-plot fractional factorial experiments has received much attention already, there are still major voids in the literature. First, designs with one or more factors acting at more than two levels have not yet been considered. Second, published work on nonregular fractional factorial split-plot designs was either based only on Plackett–Burman designs, or on small nonregular designs with limited numbers of factors. In this article, we present a novel approach to designing general orthogonal fractional factorial split-plot designs. One key feature of our approach is that it can be used to construct two-level designs as well as designs involving one or more factors with more than two levels. Moreover, the approach can be used to create two-level designs that match or outperform alternative designs in the literature, and to create two-level designs that cannot be constructed using existing methodology. Our new approach involves the use of integer linear programming and mixed integer linear programming, and, for large design problems, it combines integer linear programming with variable neighborhood search. We demonstrate the usefulness of our approach by constructing two-level split-plot designs of 16–96 runs, an 81-run three-level split-plot design, and a 48-run mixed-level split-plot design. Supplementary materials for this article are available online.     

Morphology,structure, and photovoltaic properties of poly(3‐hexylthiophene) and [6,6]‐phenyl‐C61‐butyric acid methyl ester‐based ternary blends doping with polystyrene of different tacticities

The influence of the polystyrene of different tacticities on the morphology, phase structure, and photovoltaic properties of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) blend has been extensively investigated. The atactic polystyrene (aPS) immiscible with P3HT tended to form the phase‐separated and columnar structure at low aPS weight ratio. Besides, the aPS could migrate to the surface of the films with PCBM phase distributing in the interfaces between P3HT and aPS domains at high aPS weight ratio of 75 wt %. The syndiotactic polystyrene (sPS) immiscible with P3HT could induce the crystallization of P3HT at low weight ratio of 3 wt %. The device based on aPS/P3HT/PCBM ternary blend showed of power conversion efficiency (PCE) of 1.2% even at aPS weight ratio of 50 wt %. However, the device based on sPS/P3HT/PCBM exhibited a sharp decrease in PCE value from 2.3% to 0.6% at sPS weight ratio of 3 wt %, due to the change in film morphology. The performance of the solar cell is believed to be determined by the morphology and phase structure of the ternary blends as revealed by the atomic force microscopy and UV‐vis spectra analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41823.